Tim Medical Erecaid EZ Ring
- Osbon Erecaid
- In Stock
- Calculated at Checkout
Bulk discount rates
Below are the available bulk discount rates for each individual item when you purchase a certain amount
|Buy 4 or above||and pay only $23.95 each|
Erecaid EZ Ring Buy 3 or more at $22.00 each
The unique and patented design of the EZ Ring, which fits on the end of the cylinder like a lid, ensures that the scrotal tissue is not drawn into the cylinder of the pump. This design gives many patients a more comfortable fit, provides a better seal between body and cylinder, and greater tension to assist in maintaining penile rigidity. Once an erection has been created, the ring is removed from the end of the cylinder and remains at the base of the erect penis. The EZ Ring minimizes the ring transfer process. For use with Esteem or Classic cylinders and systems.
Timm Medical, the manufacturer does not provide replacements for retailers or the end user, including broken handles. This product is purchased at your discretion.
Manufacturer: Timm Medical, AKA Osbon Medical, Timm Osbon, Osbon Erecaid
Timm Medical the manufacturer will not replace broken bands for resellers or end users.
EZ TENSION RING - Instructions for Use
The EZ Tension Ring has a unique and patented
design which allows it to easily fit directly onto the end
of the cylinder like a lid. This creates a firm seal with the
cylinder and with penile tissue which facilitates the
vacuum process. This design also ensures that the
scrotal tissue is not drawn into the cylinder when
pumping. These advantages give many patients a
more comfortable tension ring fit and more tension to
assist in maintaining penile rigidity. Once an erection
has been created, the ring is slipped off the end of the
cylinder and remains at the base of the erect penis
minimizing the ring transfer process. EZ Tension Rings
are intended for use with Esteem®
and Classic cylinders and Vacuum Therapy Systems.
Step 1 – Remove the gray insert from the end of the cylinder provided with your Vacuum Therapy
System and place the EZ Tension Ring on end of the cylinder like a cap or a lid, as shown below.
Note: DO NOT USE Ring Loader with EZ Tension Rings
Step 2 – Apply lubricant to the surface around the center of the opening of
the EZ Tension Ring as well as to the entire head of the penis.
Step 3 – Place the head of the penis against the opening of the EZ Tension Ring,
making certain that the Urethral Notch is on the bottom and the Removal Grips are on the sides.
Step 4 – Operate the vacuum pump by squeezing the handle or pressing the power button on the
pump handle. This will remove air from the cylinder and also draw the penis into the cylinder.
Allow the penis to be drawn through the opening in the EZ Tension Ring into the cylinder until the
Ring is positioned near the base of the penis.
Step 5 – Pump slowly for several seconds. Slow down or stop if you feel discomfort. Pause to let
the blood flow into your penis. Continue pumping until your penis becomes erect and lifts off the
cylinder floor and is firm enough for intercourse.
Step 6 – Press the green vacuum release button and pull the EZ Tension Ring off the cylinder, so
that the Ring remains positioned at the base of your penis.
CAUTION: Do not leave the Tension Ring on for longer than 30 minutes. Allow 60 minutes
Step 7 – Remove the EZ Tension Ring after sexual activity by pulling the Removal Grips outward,
away from the penis. Hold the grips in this position until the penis loses some firmness. Then
slowly pull the ring forward and off your penis. Additional lubricant may be needed to aid in
Step 8 – Wash EZ Tension Ring with warm soapy water, rinse and dry thoroughly for storage until
Only product I would recommend
Works well but very difficult to remove.
Works like a charm
It would be helpful if there were directions. What is the right way to apply
Works great. So much better than the ones you have to slide off or twist around. You just leave it where it is.
I have been using standard tension rings but decided to give this ring a try. EZ ring nice as one does not need to pre-load a ring EZ ring, it just needs to be attached to the end of the cylinder and lubricated. Flaccid / semi flaccid penis sucks in easily and pump up works well. Neither I nor female partner notice that the ring is larger than other rings. Great if need a fast quick second pump up! I switch between EZ ring and standard rings. Engineer
This product works great! I had to learn how to use it, but discovered it does the job! No pain at all, and no complaints with the use of this product!
EZ ring is more than a satisfactory product. as a former prostrate cancer surgery patient, i have used the rings for over 14 years with my pump. the results have been marvelous!
At 72, ED kicked in several years ago. However, it forgot to tell my brain. As an engineer, I searched to find something that would work, providing me the ability to function sexually with my wife. She is much younger than me. While the use of a pump device, along with the "EZ Ring", sort of kills the passion of the moment, at least there can be a moment... Or more than a few moments. I purchase the largest size (#7) of the "EZ Ring" offered. Using the lubricant suggested by "Erecaid", installation of the ring is fairly uncomplicated. However, when passion has met it's demise, getting the ring off the penis can be a chore. Use of the lubricant helps that effort. That lubricant is necessary for that job. Otherwise, the "EZ Ring" will have a short life and break. I suggested the device to my cousin. He was not able to make it work properly. Plus, his lady complained about the "EZ Ring" being uncomfortable for her. My wife complained, as well. However, she got over it.