Erecaid EZ Ring
- In Stock
- Calculated at Checkout
Bulk discount rates
Below are the available bulk discount rates for each individual item when you purchase a certain amount
|Buy 3 or above||and pay only $22.00 each|
Erecaid EZ Ring Buy 3 or more at $22.00 each
The unique and patented design of the EZ Ring, which fits on the end of the cylinder like a lid, ensures that the scrotal tissue is not drawn into the cylinder of the pump. This design gives many patients a more comfortable fit, provides a better seal between body and cylinder, and greater tension to assist in maintaining penile rigidity. Once an erection has been created, the ring is removed from the end of the cylinder and remains at the base of the erect penis. The EZ Ring minimizes the ring transfer process. For use with Esteem or Classic cylinders and systems.
Timm Medical, the manufacturer does not provide replacements for retailers or the end user, including broken handles. This product is purchased at your discretion.
Manufacturer: Timm Medical, AKA Osbon Medical, Timm Osbon, Osbon Erecaid
Timm Medical the manufacturer will not replace broken bands for resellers or end users.
EZ TENSION RING - Instructions for Use
The EZ Tension Ring has a unique and patented
design which allows it to easily fit directly onto the end
of the cylinder like a lid. This creates a firm seal with the
cylinder and with penile tissue which facilitates the
vacuum process. This design also ensures that the
scrotal tissue is not drawn into the cylinder when
pumping. These advantages give many patients a
more comfortable tension ring fit and more tension to
assist in maintaining penile rigidity. Once an erection
has been created, the ring is slipped off the end of the
cylinder and remains at the base of the erect penis
minimizing the ring transfer process. EZ Tension Rings
are intended for use with Esteem®
and Classic cylinders and Vacuum Therapy Systems.
Step 1 – Remove the gray insert from the end of the cylinder provided with your Vacuum Therapy
System and place the EZ Tension Ring on end of the cylinder like a cap or a lid, as shown below.
Note: DO NOT USE Ring Loader with EZ Tension Rings
Step 2 – Apply lubricant to the surface around the center of the opening of
the EZ Tension Ring as well as to the entire head of the penis.
Step 3 – Place the head of the penis against the opening of the EZ Tension Ring,
making certain that the Urethral Notch is on the bottom and the Removal Grips are on the sides.
Step 4 – Operate the vacuum pump by squeezing the handle or pressing the power button on the
pump handle. This will remove air from the cylinder and also draw the penis into the cylinder.
Allow the penis to be drawn through the opening in the EZ Tension Ring into the cylinder until the
Ring is positioned near the base of the penis.
Step 5 – Pump slowly for several seconds. Slow down or stop if you feel discomfort. Pause to let
the blood flow into your penis. Continue pumping until your penis becomes erect and lifts off the
cylinder floor and is firm enough for intercourse.
Step 6 – Press the green vacuum release button and pull the EZ Tension Ring off the cylinder, so
that the Ring remains positioned at the base of your penis.
CAUTION: Do not leave the Tension Ring on for longer than 30 minutes. Allow 60 minutes
Step 7 – Remove the EZ Tension Ring after sexual activity by pulling the Removal Grips outward,
away from the penis. Hold the grips in this position until the penis loses some firmness. Then
slowly pull the ring forward and off your penis. Additional lubricant may be needed to aid in
Step 8 – Wash EZ Tension Ring with warm soapy water, rinse and dry thoroughly for storage until
The only drawback for me is the handles on the sides to help you loss your erection, does not let the blood flow out fast enough.It makes it difficult to pull the ring off your penis.Other then that it works great. well worth the price.
The silicone EZ seal and ring makes life good again. However, trying to release the erection and remove the silicone seal over the head of my penis has proved challenging. My fat fingers have great difficulty trying to pull with enough tension on the rings, the girth of my penis doesn't allow much of a gap to form...I wish the pull rings were more in tune with my fingers. Any assistance in the r & d department would be greatly appreciated.
This ring works very well for several uses but tends to split open from the inside of the ring after additional use. Maybe this area could be beefed up a bit to give it more durability.
its very tight but with the right amount of lube, it work great for me.
Good tension and a good erection but the inner ring always breaks after several uses
Removal: Lubricate the penis just prior to ring removal. To avoid breaking handles, I put my thumb on the body side and one or two fingers on the handle side. Squeeze fingers together and pull ring for 20 seconds to allow some blood to flow out. Then slowly pull ring off penis. At first I got hair stuck under my fingers. I found that by cutting some hair back about halfway short, I eliminated this problem.
Beginning: Follow the directions. Lubricate the penis head and inside diameter of the ring opening. Apply one continuous pressure at first to pull the entire penis through and completely inside the ring.
I do this once daily. It is easy and takes less than 10 minutes. Daily is necessary to maintain penis conditioning. The EZ rings make this much move comfortable than the snap bands. No more scrotal tissue sucked in. I have four rings, one each of size 4,5,6 and 7. Only trial can tell you which size is best.
Only one drawback. My erection is 1 cm shorter with the EZ ring compared to the snap bands. I might use a snap band for the real deal. But for daily conditioning, this is the best.
Best of all rings. Could be fantastic if handles were stronger!
wow what a hard-on
I thought the simple one-dimensional rings from Erecaid that I was using were the best, This ring not only allows a great erection, but my wife loves them too.Kudos to whoever invented these things!